*NEWS*AMPS DRIVE MULTI-INKJET HEADS

[Anonymous]

Power Amplifier Drives Multiple Inkjet
Heads

march, 2005

The desktop inkjet Printer is an engineering marvel. Able to place Millions
of tiny ink Droplets precisely on a page, it creates a page of crisp type and
vivid images rivaling silver-halide photography, which has been solidly
entrenched for more than a century. Not so well known is the role inkjet
printing is beginning to play in other applications — food, beverage and medical
packaging as well as large format applications such as billboards and banners.
It is here that power operational amplifiers, such as the Apex Microtechnology
MP111FD, are fulfilling a crucial role in the design of inkjet printers

The piezoelectric technique of inkjet printing employs a crystal that flexes
whenever a voltage pulse is applied to the piezo transducer, thereby forcing a
droplet of ink out of the nozzle.illustrates this sequence.

Each time a voltage pulse is applied to the piezoelectric material, it
deforms, forcing a tiny droplet 50 to 60 microns in diameter onto the surface to
be printed. When the voltage returns to zero, the material is restored to its
original shape, drawing ink into the reservoir and thus preparing it for the
application of the next drop. This cycle repeats many times per second, each
time the print head makes a pass across the page.

Multiplexing the Nozzles

A representative printing head configuration might employ a single power
amplifier to drive 128 nozzles. A variation of time-division multiplexing is
employed. We say variation because it departs somewhat from the conventional
system of time-division multiplexing, which normally connects to just one node
at a time. In this case, the power amplifier may be connected to any number of
ports at any one instant — from 0 to 128.

Depicted  are 128 MOSFET switches that connect the
piezoelectric jet nozzles in the printhead to the power amplifier. Consequently,
at any instant, the voltage on each piezo driver is either 0 V or 48 V,
depending on whether that nozzle is on or off. As shown in the figure, each
nozzle is turned on by grounding the piezoelectric transducer via the MOSFET
switch element corresponding to the nozzle it drives. However, the high-voltage
piezo driver remains connected at all times to all of the high sides of the 128
nozzles via a bus.

The MOSFET switches control the entire ensemble digitally. The switches allow
the negative return of each piezo transducer to either float — in which case the
companion nozzle does not dispense a droplet of ink — or to be grounded, so as
to dispense a droplet of ink. At any instant, the printhead carrying all 128
nozzles is emitting anywhere from 0 to 128 ink droplets as governed by the
program instructions delivered to the bank of MOSFET switches. Perhaps numbers
12, 84 and 128 nozzles are selected, at any instant. If so, they are all driven
at that moment by the piezo transducer.

Different Waveforms for Different Inks

Various waveforms have been devised for printing various kinds of inks. These
waveshapes are developed empirically and are then stored in a computer so that
the optimal waveshape for each ink and its specific application can be retrieved
at a later time.

The simplest is a trapezoidal waveform, which has a controlled ramp on the up
slope and a ramp with a slightly different slope on the down side. These slopes
are well controlled but not necessarily symmetric. The rise on the up slope is
likely to be faster, whereas on the down slope a longer fall time is necessary.
This ensures sufficient ink will flow from the ink magazine to the nozzle
chamber to supply ink for the next droplet to be dispensed. A representative
waveform is shown

Common to all designs is a waveform that must be devised that is tailored to
the specific characteristics of the ink to be dispensed. Principal governing
factors are the viscosity of the ink, and the shape and size of the droplet to
be delivered to the printing surface and the mechanism of the printhead
itself.

For some inks, it maybe necessary to double-pulse the piezo transducer to
overcome oscillations that might hinder satisfactory ink delivery. Depending on
the ink employed, such double-pulsing can counteract oscillations that would
otherwise occur when the droplet leaves the jet.

The power amplifier must be designed to deal with any arbitrary waveshape
that may be required for a given printing solution. In other words, there is no
single circuit that will fulfill all piezoelectric ink-driver design objectives.
That is why an understanding of all the design issues is essential to developing
driver circuits.

Determining Design Parameters

Because piezo elements are almost purely capacitive and therefore dissipate
virtually no power, disposing of the heat is of paramount importance. Almost all
the buildup of power is dissipated in the power amplifier module. This must be
safely transferred as heat from the amplifier module, via thermally efficient
heatsinking, in such a way that the operating temperatures within the power
amplifier remain safely below its rated safe operating temperature.

The Apex MP111FD power operational amplifier is particularly suited for
driving piezoelectric transducer arrays. It is a 100-V device with a 500-kHz
power bandwidth and a 50-A pulse capability. shows a simplified
drawing of the MP111FD power operational amplifier in an inkjet transducer
application with the companion passive components identified.

Next, we examine the essential steps in designing the piezo transducer
circuit. The first step is choosing power supply voltages. An unbalanced source
voltage would be best. Assuming a 50-V pulse is to be delivered by the power
amplifier, then a +62-V and a -12-V source would be appropriate. This will
assist the charge-discharge cycle because the capacitive load presented by the
array of tranducers must be driven back to 0 V during each pulse cycle.

As the capacitor approaches 0 V, the -12-V potential will ensure that the
output transistor of the power amplifier will still have sufficient potential to
drive the capacitor back to 0 V. This minimizes the power dissipation in the
amplifier and also contributes to signal fidelity.

The next step is selecting passive component values. Assuming a gain of 10,
the value of R_I would be 100 Ω, R_F
is 1 kΩ and capacitor C_C is 33 pF to 47 pF.

Once those values are selected, the designer must address stability issues.
Because the load is highly capacitive, a resistance R_S may
need to be placed in series with C1 to improve the stability of the amplifier
circuit. You will have to experiment, but typical values for
R_S will range from 0.1 Ω to 0.5 Ω, depending on the
capacitance of the printhead. Without R_S, there may be
considerable overshoot in the output waveform, which could affect the droplet
shape and the overall performance of the system.

The next task is bypassing the power supply terminals. Because the slew rate
of the power amplifier is quite high, there is a tendency for the power supply
to droop if no precautions are taken. It is recommended that two 1-µF ceramic
capacitors of the leadless surface-mount type, C_BP, be
connected directly to the +V_S and
-V_S pins of the power amplifier.

After bypass caps are added, it is necessary to enhance dynamic response. To
do so, connect a series network comprising a 10-p_FSH and a 1-kΩ resistor
R_SH in shunt with resistor R_F, as
shown in This will improve the dynamic response of the power
amplifier. Adjust these values slightly to optimize the response.
capacitor C

Another step is minimizing distortion. As the amplifier slews, it forces
energy back into the signal source. To minimize distortion that might otherwise
occur, it is essential the signal source exhibit a low dynamic impedance of 1 W
or less.

Selecting a Heatsink

It is essential to hold the junction temperatures within the power amplifier
module below 175°C. Determining the proper heatsink is a three-step procedure.
First, the average power consumption is determined. Then, the thermal
resistivity in °C per watt of the heatsink is calculated. Finally, the thermal
resistivity of the heatsink selected is checked to ensure it provides sufficient
margin. That is, it will hold the junction temperatures to a value well below
175°C.

• Determining power dissipation

  Once the waveform for a particular ink is determined, a simplified circuit
  can be devised to perform a SPICE simulation and thereby determine the power
  that will be dissipated within the amplifier. shows a simplified
  SPICE circuit that represents the MP111FD power operational amplifier circuit.
  In this example, the amplifier is assumed to be driving four inkjet printheads
  simultaneously.

  Each printhead will be assumed to have 256 nozzles for a total of 1024
  nozzles. The total capacitance of the four heads is 1 µF. However, only every
  third nozzle is driven at any instant. Therefore, the maximum capacitance in
  this analysis is reduced to 0.33 µF. This is the load capacitance identified as
  C1
  

  A piece-wise linear waveform is developed by V8 that duplicates the selected
  waveform, as illustrated in  The results of the SPICE simulation

  are depicted by the three graphs in.

  Plot 1 depicts the amplified output voltage waveform V(1). Plot 2 is the
  current pulse train I(C1) applied to the load capacitor C1, whereas Plot 3 shows
  the average power dissipated in the amplifier versus time:

  Average Power = AVG {[(V1)-V(6)]*[I(V6)]+[(V(1)-V(4)]*[I(V7)]} (Eq. 1)

  Plot 3, as governed by this equation, is the average of the voltage across
  each output transistor multiplied by the current through each transistor at each
  instant in time. The result at the end of the period is the average power that
  the heatsink must dissipate due to the load. It is this average power, 68 W,
  which is of interest in determining the heatsink requirement.

  Because the pulse rate frequency is 30 kHz, its period is 33.33 µs. Notice
  that in Plot 2 the current pulses end after 16 µs. The remainder of the period
  is dead time. Therefore, the time interval for the average is greater than the
  time over which instantaneous energy is being delivered. Therefore, 68 W is the
  average power that must be dissipated by the amplifier over the full period.

• Determining heatsink requirements

  By referring to the data sheet for the MP111FD, the ac thermal resistance is
  determined to be 0.65°C/W. To calculate the temperature rise of the junctions of
  the output transistors above the case temperature, multiply the thermal
  resistance of the MP111FD by the average power dissipated:

  0.65°C/W * 68 W = 44.2°C (Eq. 2)

  To determine the permissible case temperature, assume that a normal ambient
  temperature within the printer will be 30°C. The maximum operating case
  temperature of the MP111FD is 85°C. Thus, subtract the ambient from the maximum
  operating temperature to determine the permissible case temperature rise:

  85°C – 30°C = 55°C (Eq. 3)

  Therefore, the permissible case temperature rise is 55°C.

  Although the load, C1, dissipates 68 W of power in the amplifier, the
  heatsink will have to dissipate the quiescent power dissipation of the amplifier
  as well as the power delivered by the pulse train.

  The quiescent power dissipation of the MP111FD with the operating conditions
  given is approximately 11 W. This quiescent power is due to the operating power
  supply voltages and the quiescent current in the amplifier. Therefore, the
  actual amount of power that must be dissipated is the sum of the two, or 79 W.
  The thermal resistance of the heatsink required is governed by this
  equation:

  (X°C/W) * (79 W) = 55°C (Eq. 4)

  Where X is the required heatsink thermal resistance in °C/W; 79 is the total
  amplifier dissipation in watts; and 55 is the permitted temperature rise of the
  amplifier in °C.

  Solving equation 4 for X yields a thermal resistance of 0.696°C/W. Thus, any
  heatsink having a thermal resistance of 0.696°C/W or less will be acceptable in
  this application.

• Confirming the maximum junction temperature

  Although a maximum junction temperature of 175°C is allowed, for long-term
  reliability, a lower temperature would be better. Check that a heatsink with a
  thermal resistance of 0.696°C/W will hold the junction temperature of the output
  transistors below 175°C.

  As previously mentioned, the 68 W of power dissipation due to the load causes
  a temperature rise of 44.2°C in the output transistors. The total junction
  temperature with the selected heatsink is then the sum of the maximum case
  temperature and the temperature rise in the output transistors:

  85°C + 44.2°C = 129.2°C (Eq. 5)

  Where 85°C is the case temperature with the selected heat sink and 44.2°C is
  the temperature rise of the output transistors due to the load. Because a
  junction temperature of 175°C is the maximum allowed, there will be a margin of
  45.8°C — acceptable for the heatsink in this application.

  If the power module is to be located near the printhead and the ink is
  heated, the operating ambient will be well above room temperature of the
  traditional 25°C. In this case, liquid cooling or forced air may be
  required.

  Note that for illustration purposes, the quiescent current in the output
  stage and some other fine details have been neglected. However, Apex has an
  online power design spreadsheet that can easily help you with all the details of
  arriving at a heatsink thermal resistance for your particular application. Log
  on to WWW. APEXMICROTECH.COM And look for
  “Circuit Design Software” under the “Support” icon.

  As we have shown, devising a drive circuit for inkjet circuits requires
  tailoring a waveform that will optimize the delivery of the ink droplets
  delivered by a particular printhead. Then, by following the sequence of steps
  described, the designer will be able to configure a driver circuit that will
  provide the necessary current pulse train and preserve the fidelity of the
  waveform delivered to the printhead, while addressing the resulting thermal
  issues

[Author]

March 16, 2005 at 9:39 AM